|[User Record Capacity]||1000persons|
|[Face image Capacity]||N/A|
|[Display Screen]||2.4inch color screen|
|[Communication Mode]||USB flash disk drive USB cable|
|[Fingerprint Acquisition]||Green light fingerprint entry device|
|[Voice Broadcast]||Human voice|
|[Power Supply]||DC 5V 1A|
Green light fingerprint without membrane;
Automatically and directly output attendance reports;
It also upports double U( U disk and USB cable) to upload and download at high speed.
The ink capacity in many opaque tube of Ball Point Pen can not meet the International Standard of GB/T4306-92, actually, there is only 1-2 cm ink near the tube. And for some transparent refill tube , about 1 cm ink near the tip no problem ,but the rest can not write out.
Inferior ink can not write under the temperature of 0-40 centigrade according to International Standard. It will leak when the weather is too hot ,and freeze when the whether is too cold.According to International Standards, the self life for ball point pen is 2 years. But the self life for high quality ball point pen can be up to 3 years. Whereas, the ink for low quality ball point pen will dry out within several months.
In accordance with international standards, the writing angle for ball-point pen is 47 degree. But for low quality ball point pen can only write when the angle is 90 degree.(The best way to test the ball-point pen is anticlockwise drawing circle with the holding angle 47 degree.)Most barrel of Ball-point pen & Gel pen is made from plastic. For the low quality products, the plug which fixed the refill is easily slide, there is neither bayonet nor any sticky material between the plug and the end of pen barrel, the plug is easily to spring out since it totally depends on the pen's tension. When you write strongly, the plug also easily bounce off.
Gel Pen is an emerging product which has no any National Standard for the moment. Because of the bad technologies, many factories not focus on quality but on quantity during the production. Thus such the problems as ink agglomerating, crystallization etc. appear easily in their products, especially the gel ink pen with 0.5MM and 0.38 mm pipe tip which can not meet with the Standard totally. Most of them can not even write out within 3-5 months.Inferior ink causes many problems which influence the writing smoothness even occurring the ink spitting and oozing. If we draw a straight line quickly and lightly with the same holding angle as the ballpoint pen, high quality pens will produce a continuous line with even color, not a heavy or thin line. Then, if we slowly draw a folding line with the common writing pressure while keeping the same holding angle as the ballpoint pen, high quality pens will produce an even color line without ink gathering or oozing even without the ink gathering point when putting a pen. Furthermore, if drawing circles quickly in counter-clockwise with the same holding angle, people can feel the smooth writing by using superior pens.
Besides the ink problem, inferior gel pens also have many other problems such as bad materials of the tip balls, coarse cavity of the tip pipes, bad elasticity and leak tightness of the wax on the tip etc. All these factories will lead some writing problems after long time storing or during the transportation.
> type and color of ink
> type and size of tip
> colors of barrel
> design of logo
> type and artwork on the packagecan be advised depending on the model you choose.
1) The tip ball can’t turn because of factitious damage.
2) The inner part of tip is blocked.
3) The ink can’t flow out because of the ink groove of the tip inner part is wore .
4) The shelf life is exceeded and the ink has been deteriorated.
5) The air exposure has been so long that the ink has been dried.
1) The slight air bubble exist in the ink of the refills
2) The silicon oil upper the refill has gone into the ink layer
3) There is oil in the paper making the writing skidding.
4) Little impurity or deteriorated dissociation exist in the ink of the refill.
1) The tip is slightly damaged causing the tip ball doesn’t turn smoothly
2) The end gap of the tip ball is in different size.
1) The end part of tip ball is too big or the exposed tip is too much.
2) The edging part of the tip ball is worn badly during wring.
3) It damaged by human reason.
4) It is greatly impacted in exposure.
1) The tip ball is fell down so that the ventilation is good in the refill
2) The air is too much in the ink of the refills.
3) The silicon oil in the upper part of refill has chemical reaction with the ink layer, so that it doesn’t function as floating plug.
4) The exposure is too long so that the ink is dried. The air flows in and the up-side down is too long.
5) Being greatly impacted in exposure.
6) To write in a upside down position or in a sub-pressure (vacuum) condition.
Step 1: Make sure that the small, plastic ball has been removed from the pen's tip. When a gel pen is new, it is shipped with a small piece of plastic on the tip to prevent the pen from leaking during shipment.
Step 2: Move the pen in circular motions on a scrap piece of paper. This facilitates the ink flow to the point of the pen.
Step 3: Shake the pen briskly. This will help to dislodge any air bubbles which may be preventing proper ink flow to the tip.
Step 4: Heat the tip of the pen over a kettle or a pot of hot water. This helps to loosen the ink, which can congeal if the room temperature is too low.